KokodaTrailModels on Shapeways

Jeremy Stevenson

KokodaTrailModels

3D modeler

Full Time Cartographer, Part Time Designer. Australian, Male, 35, no, wait, make that 27 years old. Queenslander and proud of it!

138
Followers

0
Following

KokodaTrailModels's

KokodaTrailModels

April 8, 2018

http://shpws.me/Q8Sx

cwcs2010 Hello, 'KokodaTrailModels'. Can You make a new 1/700 BTR-80 Models based on your BTR-4's ? Your present BTR-80 Models have a slight flaw that most front end of your BTR-80's wheel is in front of your BTR-80's driver's seat. This is same to all the other of your BTR-80 based vehicle models such as BTR-82A and 2S23 Nona SVK, except the BTR-4 varionts. So I think if you make a 'new' 1/700 scale BTR-80 and it's variation vehicle model based on your already made 'BTR-4' would be very thankfull. Please give me your replies to me. I will happly wait your answers.

September 4, 2022

KokodaTrailModels @juanrosario2115 Yes, they’re still available.

KokodaTrailModels @agentnot007 Almost looks like a spy satellite photo from the 1990!

KokodaTrailModels @agentnot007 An awesome color to paint those small models!

KokodaTrailModels @agentnot007 very fine paintwork! In 1:700 these helos are tiny.

KokodaTrailModels @agentnot007 Amazing paintwork!

KokodaTrailModels @JeffyB Sure, here it is - https://www.shapeways.com/product/VNKUXMDWP/1-600-canberra-bomber-x12

KokodaTrailModels @agentnot007 they are looking awesome!

KokodaTrailModels @agentnot007 they’re looking awesome!

KokodaTrailModels @JeffyB Sure can - https://www.shapeways.com/product/DJKR7VULP/1-600-ng-31-nyala-mamba-mk-2-apc-company

KokodaTrailModels @JeffyB https://www.shapeways.com/product/M5YMGZ8N2/1-600-casspir-infantry-mobility-vehicle-company

KokodaTrailModels @JeffyB OK, done, check the 1/600 Section of my shop tomorrow.

KokodaTrailModels @JeffyB Good to hear you like them. Let me know which ones specifically you'd like to see in 1/600, as there's probably too many for me to make in that scale in one go.

KokodaTrailModels @jiv25 Yes - https://www.shapeways.com/product/R6KGBGM2F/1-600-mig-29-fulcrum-x12

KokodaTrailModels @Dioramaman Hi Dioramaman, Agreed, making WSF smooth is nearly impossible, especially for models with fine parts like periscopes, or ordinance on an aircraft. I'd recommend Frosted plastic, except for the massive price difference. WSF is good for objects that don't require a smooth surface, like stealth aircraft, or buildings.

KokodaTrailModels @paratrooper629 you can still buy all of my products here. I just don't do modifications.

KokodaTrailModels @rebelmodel Unfortunately the RAH-66 is too small to print in scales below about 1/72 without making the parts too chunky, and in a scale as large as that Shapeways would charge about a million bucks to print it.

KokodaTrailModels Hi rebelmodel, The price would end up the same as they would need extra plastic to joint the 16 together.

KokodaTrailModels @marks4god Unfortunately not, as most of the parts are smaller than 0.5mm like landing gear.

KokodaTrailModels @mmaresm - Thanks, those were some of my favorite designs as they did turn out as I originally started with ease.

KokodaTrailModels Hi KingKaddish, Thanks for you interest in my models. Unfortunately all my models are designed in 1/700 with the smallest allowable print sizes. That means that quite a few parts, like landing gear, or detail on a fuselage are at the threshold of what can be printed (0.1mm - 0.5mm). Making a model smaller than 1/700 (ie 1/1400) is impossible, and due to time constraints a redesign is also not possible. Cheers, Jeremy KTM